设备主要特点Main features of equipment
一、油浴式电加热喷体：
1、喷体温度均匀，温度稳定，温度波动保证在≤0.1℃以内（解决了由于加热温度不均匀造成的丸子大小头、假合缝等问题）。
2、由于温度精度高可以降低胶片厚度0.1mm左右（节省明胶约10%左右）。
二、计算机自动调整注药装量
1、自动调整装量，节约时间，节省原料。
2、装量精度高，装量精度为≤±1%，大大降低原料的损耗。
三、换向板、上下本体、左右垫条硬度达到HRC60-65.经久耐用：适合用户生产各种液体混悬中药品种，大大的提高了使用寿命。
四、模具锁盘（三点锁定）：锁定后不跑线，同时兼有微调功能，操作非常简单。
五、微量润滑系统：油量根据转速自动调节。（降低石蜡油耗，节约成本）
六、内置冷风系统，配备冷水机。
七、胶皮滚采用单独变频调速：生产时如果胶液质量不好可通过胶皮滚调速来解决。
八、出丸区冷风定型设计；避免拉网轴缠网胶，使胶囊成型更美观 。
九、模具下丸部分采用特殊的斜斗，清洗非常方便。
十、供料泵与机头采用外侧传动，供料泵内的润滑油不会进入机头。（供料泵独立密封）
Oil bath electric heating spray body: The temperature of the spray body is uniform, the temperature is stable, and the temperature fluctuation is guaranteed to be within ≤ 0.1 ℃ (solved the problems of the ball head and false joint caused by uneven heating temperature) Due to the high temperature accuracy, the film thickness can be reduced by about 0.1mm (saving about 10% of gelatin).Second, the computer automatically adjusts the injection volume
Automatically adjust the loading volume, save time and save raw materials. The loading accuracy is high, and the loading accuracy is ≤ ± 1%, which greatly reduces the loss of raw materials. The hardness of the reversing plate, upper and lower bodies, left and right pads reaches HRC60-65. Durable: suitable for users to produce various liquid suspension Chinese medicine varieties, greatly improving the service life.Fourth, the mold lock disk (three-point locking): does not run the line after locking, and also has a fine-tuning function, the operation is very simple.
Trace lubrication system: The oil quantity is automatically adjusted according to the speed. (Reduce paraffin oil consumption and save costs) Built-in cold air system, equipped with chiller. The rubber roller adopts a separate frequency conversion speed regulation: if the quality of the glue is not good during production, it can be solved by the rubber roller speed regulation. Cold air setting design in the pill-out area; avoid entanglement of the mesh with the mesh and make the capsule more beautiful.Nine, the lower part of the mold uses a special inclined bucket, which is very convenient to clean.
The feed pump and the machine head are driven outside, and the lubricating oil in the feed pump will not enter the machine head. (The feed pump is independently sealed)技术参数：Technical Parameters:
型号Model | RJN-65 | RJN-100 | RJN-250 |
滚模额定转速Rolling mould rated speed | 0-5r/min | 0-5r/min | 0-5r/min |
滚模尺寸Rolling die size | Φ64×65mm | Φ64×100mm | Φ150×250mm |
单柱塞供给量Single plunger supply | 4x(0-2ml) | 6x(0-1.5ml) | 20x(0-1.5ml |
装量精度 Loading accuracy | ±1% | ±1.5% | ±2% |
产量Yield（0.5g） | 8900粒/小时 | 15600粒/小时 | 76000粒/小时 |
电压Voltage | AC220V50HZ | AC220V50HZ | AC380V50HZ |
总功率Total power | 3.6kW | 4.2KW | 12KW |
主机外形尺寸Host size | 1400x700x1660mm | 1400x700x1660mm | 1980x850x1860mm |
65型 辅 机 （标 配） 65 type auxiliary machine (standard) | |||
定型转笼 Stereotype cage | 转笼尺寸：φ320x450mm 转速：21转/分钟 Rotating cage size: φ320x450mm speed: 21 rpm | ||
化胶罐 Plastic tank | 容积：30L 带保温、搅拌及仪表电器控制 Volume: 30L with insulation, mixing and instrument electrical control | ||
不锈钢胶体磨Stainless steel colloid mill | 细度：20-70微米 转速：3200转/分 Fineness: 20-70 microns Speed: 3200 rpm | ||
冷水机 Chiller | 制冷温度：-5～16度 Refrigeration temperature: -5 ~ 16 degrees | ||
晾干盘 Drying tray | 托盘尺寸：720x520x50mm 数量：20个 Tray size: 720x520x50mm Quantity: 20 | ||