恒流高压电源 800V5开关电源 0-800V5A可调直流稳压电源

 

 

SNK-4KW开关直流稳压电源

Snk-4kw switch  DC regulated  power  supply

 

恒流高压电源  800V5开关电源 0-800V5A可调直流稳压电源

 

一：产品概述： Product overview

l 输出电压可5V-3000V任意电压可定制

l Output voltage can be 5v-3000v, any voltage can be customized

l 电流电压数码显示，3 1/2位显示

l Current and voltage digital display, 3 1 / 2-bit display

l 具备软启动、缺相、过热、限压、限流、短路、超载等保护功能

l It has the protection functions of soft start, phase loss, overheating, voltage limit, current limit, short circuit, overload, etc

l 优异的动态响应时间<20ms

l Excellent dynamic response time < 20ms

l 48小时满载老化测试

l 48 hours full load aging test

l 输出连续可调，恒流恒压双模式

l Output continuously adjustable, constant current and constant voltage dual mode

l 远程选配标配；可选配模拟量/RS485/RS232远程控制接口；可实现远程控制电源电压，电流，开关及电压电流在电脑或PLC显示；

l Remote optional standard configuration; optional analog quantity / RS485 / RS232 remote control interface; remote control power supply voltage, current, switch and voltage current can be displayed in computer or PLC

 

二：产品技术参数：Product technical parameters

 

输    入: Input		AC380V±10% 50Hz/60Hz（可定制Customizable）
功    率:power		4000W
产品型号:Product model		参考选型表Refer to model selecion table
输出电压:output voltage		参考选型表Refer to model selection table
功率因素:Power factor		功率因数0.95以上Power factor above 0.95
效    率:Efficiency		≥90%
产品重量Product weight		25Kg
电压参数 Voltage parameter	负载效应 Load effect	＜1%直流输出额定值  < 1% DC output rating
	源效 应 Source effect	＜±0.3%直流输出电压额定值 ＜± 0.3% DC output voltage rating
	时  漂Time drift	＜1%额定值 < 1% rated value
	温   漂 Temperature drift	＜0.04%额定值/度 ＜ 0.04% rated value / degree
电流参数 Current parameters	负载效应 Load effect	＜1%直流输出额定值 < 1% DC output rating
	源效 应 Source effect	＜±0.3%直流输出电压额定值         ＜± 0.3% DC output voltage rating
	时  漂Time drift	＜1%额定值< 1% rated value
	温  漂 Temperature drift	＜0.04%额定值/度 ＜ 0.04% rated value / degree
纹波Ripple	电压纹波 Voltage ripple	≤1%直流输出额定值（5HZ～1MHZ）           ≤ 1% DC output rating (5Hz ～ 1MHz)
	电流纹波 Current ripple	≤1%直流输出额定值（5HZ～1MHZ）           ≤ 1% DC output rating (5Hz ～ 1MHz)
启动/停止Start / stop		本地、远程（选配）Local, remote (optional)
电  流Electric current		恒压限压控制，3 1/2位显示 ，0-10V或4-20mA模拟量控制（选配） Constant pressure limit control, 3 1 / 2-bit display, 0-10V or 4-20mA analog quantity control (optional)
电  压Voltage		恒流限流控制 ，3 1/2位显示，0-10V或4-20mA模拟量控制（选配） Constant current limit control, 3 1 / 2-bit display, 0-10V or 4-20mA analog control (optional)
保  护Protection		具备软启动、缺相、过热、限压、限流、短路、超载等保护功能 With soft start, phase loss, overheating, voltage limit, current limit, short circuit, overload and other protection functions
冷却方式Cooling mode		风冷Air cooling
环境要求 Environmental requirements		室内使用，-20℃～60℃，相对湿度＜90%未凝结水滴（25℃） Indoor use, - 20 ℃ ~ 60 ℃, relative humidity < 90% non condensed water dro (25 ℃)
产品尺寸 Product size		480*500*180mm（长*宽*高）(L * w * h)

 

 

 

三:产品选型表：Product selection table

 

 

 

四：产品面板图Product panel diagram

 

 

五：产品尺寸图Product dimension drawing

 

 

六：产品行业应用：Product industry application

 

 

1. LED、节能灯等灯具测试及老化

1. Testing and aging of LED, energy saving lamp and other lamps

 

2. 开关电源、电源适配器老化

2. Aging of switching power supply and power adapter

 

3. 光伏、逆变器测试老化

3. Photovoltaic and inverter test aging

 

4. 航空航天、国防军工

 

4. Aerospace, national defense and military industry

 

5. 电动车电机、控制器、直流马达测试及老化

 

5.Electric vehicle motor, controller, DC motor test and aging

 

6. 电容器、电阻、继电器、晶体管、传感器等电子器件

6.Capacitors, resistors, relays, transistors, sensors and other electronic devices

7. 电解、电镀、腐蚀铝箔加工等液晶屏、触摸屏等显示器

7. LCD, touch screen and other displays such as electrolysis, electroplating, corrosion aluminum foil processing, etc

8. 汽车电子、直流电机、电机控制器、点烟器、影音测试老化等
 8. Automobile electronics, DC motor, motor controller, cigarette lighter, audio-visual test aging, etc

 

 

七：产品场景应用（选择充电及产品老化说明）：

 Product scenario application (selec charging and product aging instructions)

 

一：充电场景：Charging scenario

我司电源可以模拟充电器充电，可以给任意电池进行充电：

Our power supply can simulate charger charging and can charge any battery:

 

参考三元锂电池20串 500AH电池，此电池充电电压为84V，充电最大电流为50A，

 

选择一款100V60A的我司产品，电压调到3V以内，再输出正负极短路，设置电流到50A，再断开短路，并把电压调到84V并接上电池，按启动键，充电器就会按84V50A恒流恒压模式充电，刚开始电源电压会拉低，这说明电池电量不足，等电压上升到84V，则电池充满。其他电池相同原理

Refer to 20 series 500ah batteries of ternary lithium battery, the charging voltage of the battery is 84v, and the maximum charging current is 50A,

 

selec a 100v60a product of our company, adjust the voltage to within 3V, output the short circuit of positive and negative poles, set the current to 50a, disconnect the short circuit, adjust the voltage to 84v and connect the battery, press the start button, the charger will press 84v50a constant current and voltage mode to charge, at the beginning, the power supply voltage will be pulled low, which means that the battery power is insufficient, when the voltage rises to 84v, the battery will be full. Same principle for other batteries

 

 

一：老化场景应用：Aging scenario application

   我司电源可以给任何需要直流供电的产品用于老化供电，可以恒流或恒压模式供电

Our power supply can be used for aging power supply for any product requiring DC power supply, and can supply power in constant current or constant voltage mode

 

 

 

 

1，恒压模式设置：1. Constant pressure mode setting:

   先把电压旋钮逆时针扭到最小，电流旋钮顺时针扭到最大，再根据需要调节自己所需要的电压，恒压灯亮则为恒压模式，此状态可以恒压供电，负载所需电流只要不超过额定值，则正常输出，如果负载所需电流超过额定值，则电压增低，直到无输出，断开负载恢复正常。

First turn the voltage knob to the minimum anticlockwise and the current knob to the maximum clockwise, and then adjust the required voltage as required. When the constant voltage light is on, it is the constant voltage mode. In this state, the constant voltage power supply is available. As long as the current required by the load does not exceed the rated value, the output is normal. If the current required by the load exceeds the rated value, the voltage increases until there is no output, and the load is disconnected to recover Normal.

2，恒流模式设置：Constant current mode setting

   选择恒流模式，需先把电压调到3V以内，再把电流旋钮逆时针扭到最小，输出正负极短路，再根据显示，设置所需的电流，断开短路，电压调到所需要的电压，或顺时针直接最大输出即可。

 

To selec the constant current mode, first adjust the voltage to within 3V, then turn the current knob anticlockwise to the minimum, output the positive and negative pole short circuit, then set the required current according to the display, disconnect the short circuit, adjust the voltage to the required voltage, or directly output the maximum clockwise.

 

注意：如果有操作不明白，烦请咨询我司技术人员

If you do not understand the operation, please consult our technical personnel

 

 

八：功率选择及线材匹配：Power selection and wire matching

 

1，感性负载建议按负载峰值电流选配直流电源，长期24小时工作按80%使用选配，阻性负载按90%使用率选配，如果短时间使用，比始一天只使用几小时，可以按95%使用率选配，我们产品是足功率，但需要保护我们的设备，延长使用寿命，所以功率选择时请考虑。

   

   1. It is recommended to selec DC power supply based on peak load current for inductive load, 80% for long-term 24-hour operation, and 90% for resistive load. If it is used for a short time, it can be selected based on 95% for only a few hours a day. Our product is full power, but we need to protect our equipment and extend its service life, so please consider power selection.

 

 

 

2，输入电输出线缆需客户按现场情况进行配套，我司不予提供，按1平方线缆输出3A来计算，总功率/电压=输出电流/3=所需线缆平方。

 

   2. The input and output cables shall be matched by the customer according to the site conditions, which will not be provided by our company. The total power / voltage = output current / 3 = required cable square.

 

 

购买七大钡思那电源理由：

Reasons for purchasing seven beisina power supplies

1，保护齐全，功率足，稳定性好

1. 1. Complete protection, sufficient power and good stability
   2，独特的烤漆工艺和配色，使直流电源外观美观大方
2. 2. The unique paint baking process and color matching make the appearance of DC power supply beautiful
   3，工业品质，产品采用品牌器件及相关部件
3. 3. Industrial quality, brand devices and related components
   4，QC检测，使每台电源都能满足客户需求
4. 4. QC inspection, so that each power supply can meet the needs of customers
   5.性价比高，可以迎合中高端应用行业
5. 5. High cost performance, which can cater to the middle and high-end application industry
   6.保修期2年，保修期内无需客户端出任何费用即可享受我司售后

6. The warranty period is 2 years. During the warranty period, you can enjoy our after-sales service without any cost fro the client